Pilot-RC 88in (2.24m) Skywolf V2

  Click On Images to Enlarge

Overview

A true aeromodel, designed for pure fun and simplicity. From slow flight to fun-fly and even some 3D, this is a surprisingly capable acrobatic model. Designed by Jan Spatny from Czech Republic.

Specifications:

Model:	Sky-Wolf V2
Wingspan:	88in (2,240mm)
Length:	75in (1.930mm)
Wing area:	1,400sq in (9,040sq cm)
Weight:	16 lbs (7.3kg)

Features

• Strong yet light weight design, good for aerobatic flying and can even hover!
• Highly prefabricated, experienced builders can have air ready in under a day
• Pre-installed hinges on ailerons, flaps and rudder (glued and sealed)
• Internally mounted cowling – so no external screws exposed
• Removable wings with quick release system
• Laser engraved motor mounting position
• Open construction allows for easy canister installation for 30-60cc size engine
• Quick release front windshield / top-hatch, allowing easy access to replace batteries in electric setups
• Big 5in wheels

Included Hardware:

• Complete air frame with all basic accessories (such as carbon fibre undercarriage, tail-gear assembly and wing-tubes as well as fibreglass control horns and wheel pants)
• Pre-installed hinges and pre-mounted canopy
• Fuel tank and fuel tubing pre-prepared, fuel dot and breather valve
• Wheels and wheel axels
• Pre-prepared pushrods with ball links
• Matching carbon spinner

Required Hardware:

Motor: 30-60cc or equivalent electric

Servos: 7 high torque plus throttle // Uses x1 per aileron, x1 per flap, x1 per elevator and x1 on rudder

Also requires all the usual accessories such as transmitter, receiver, propeller, batteries, powerbox, extension leads and possibly other small accessories.

Recommended Hardware (Not Supplied)

• Servos: MacGregor MG7232HV 31.5Kg.cm/0.09s High Voltage Servo or MacGregor MGB6928HV 28Kg/0.06s Brushless High Voltage Servo
• Servo arms: Pilot-RC 1.6in Aluminium arms (PIL302)
• Engine: DLE-55 | DLE-55RA | EME60 | EME-60AS (with Auto Start)
• Electric Motor: Dualsky GA3000 ~ GA6000 Series X-Motor

Colour Scheme Covering References:

Skywolf (Green/Blue - 04)

• PIL012-6 - Pilot-RC Green Covering (2m x 640mm)
• ACC0185 - MacGregor RC Sky Blue Covering Film (638mm x 2m)
• ACC0201 - MacGregor RC Indigo Covering Film (638mm x 2m)

Skywolf (Orange/White - 05)

• ACC0187 - MacGregor RC White Covering Film (638mm x 2m)
• ACC0206 - MacGregor RC Orange Covering Film (638mm x 2m)

Video

Motor: Dualsky GA4000 / ESC: Dualsky 120A / Prop: 22 x 10 wood

 

 

Gallery

Build Information:

Cowl Size

A: 225mm | B: 177mm | C: 227mm | D: 166mm

Exhaust Tunnel Size

A: 557mm | B: 83mm | C: 557mm | D: 90mm | E: 126mm | F: 166mm

Rudder Horns and Pull Pull Location

A: N/A | B: N/A | C: N/A | D: 37mm | E: N/A

Extension Wire Lengths

• Throttle: 0cm
• Each wing: Flap 15cm | Aileron 65cm (to reach receiver direct)
• Each elevator: 70cm
• Each rudder servo: 85cm

Centre of Gravity

155mm - Measured back from leading edge of the wing at the fuselage.

You will find a laser engraved C.G. emblem on the inside of the fuselage, located close to the wing tube, which also shows the exact location for Center of Gravity.